logo
Good price  online

products details

Created with Pixso. Home Created with Pixso. Products Created with Pixso.
TI Chips
Created with Pixso.

UCC28084DR TI Chips 8-PIN CURRENT MODE PUSH PULL PWM CONTROLLERS WITH PROGRAMMABLE SLOPE COMPENSATION

UCC28084DR TI Chips 8-PIN CURRENT MODE PUSH PULL PWM CONTROLLERS WITH PROGRAMMABLE SLOPE COMPENSATION

Brand Name: TI Chips
Model Number: UCC28084DR
MOQ: 2500
Packaging Details: 2500PCS/reel
Payment Terms: T/T
Detail Information
Place of Origin:
China
Document:
Model:
UCC28084DR
Product Name:
TI Chips
Type:
SMD/SMT
Switching Frequency:
1 MHz
Output Voltage:
4.3 V
Output Current:
1 A
Supply Ability:
1000000
Highlight:

UCC28084DR

,

UCC28084 TI Chips

,

8 PIN PWM Controllers

Product Description

TI Chips UCC28084DR 8-PIN CURRENT MODE PUSH-PULL PWM CONTROLLERS WITH PROGRAMMABLE SLOPE COMPENSATION


FEATURES
Programmable Slope Compensation
Internal Soft-Start on the UCC38083/4
Cycle-by-Cycle Current Limiting
Low Start-Up Current of 120 µA and 1.5 mA
Typical Run Current
Single External Component Oscillator
Programmable from 50 kHz to 1 MHz
High-Current Totem-Pole Dual Output Stage
Drives Push-Pull Configuration with 1-A Sink
and 0.5-A Source Capability
Current Sense Discharge Transistor to
Improve Dynamic Response
Internally Trimmed Bandgap Reference
Undervoltage Lockout with Hysteresis

APPLICATIONS
High-Efficiency Switch-Mode Power Supplies
Telecom dc-to-dc Converters
Point-of-Load or Point-of-Use Power Modules
Low-Cost Push-Pull and Half-Bridge
Applications

DESCRIPTION
The UCC38083/4/5/6 is a family of BiCMOS pulse width
modulation (PWM) controllers for dc-to-dc or off-line
fixed-frequency current-mode switching power
supplies. The dual output stages are configured for the
push-pull topology. Both outputs switch at half the
oscillator frequency using a toggle flip-flop. The dead
time between the two outputs is typically 110 ns, limiting
each output’s duty cycle to less than 50%.
The new UCC3808x family is based on the UCC3808A
architecture. The major differences include the addition
of a programmable slope compensation ramp to the CS
signal and the removal of the error amplifier. The current
flowing out of the ISET pin through an external resistor
is monitored internally to set the magnitude of the slope
compensation function. This device also includes an
internal discharge transistor from the CS pin to ground,
which is activated at each clock cycle after the pulse is
terminated. This discharges any filter capacitance on
the CS pin during each cycle and helps minimize filter
capacitor values and current sense delay.
The UCC38083 and the UCC38084 devices have a
typical soft-start interval time of 3.5 ms while the
UCC38085 and the UCC38086 has less than 100 µs for
applications where internal soft-start is not desired.
The UCC38083 and the UCC38085 devices have the
turn-on/off thresholds of 12.5 V / 8.3 V, while the
UCC38084 and the UCC38086 has the turn-on/off
thresholds of 4.3 V / 4.1 V. Each device is offered in 8-pin
TSSOP (PW), 8-pin SOIC (D) and 8-pin PDIP (P)
packages.

BASIC APPLICATION
UCC28084DR TI Chips 8-PIN CURRENT MODE PUSH PULL PWM CONTROLLERS WITH PROGRAMMABLE SLOPE COMPENSATION